Sat, Sep 6, 2014

Salt City Drift 9/6/14

Miller Motorsports Park

About this event

DRFTutah Presented by http://innovative-garage.com/

Come enjoy an open drift day at Miller Motorsports Park in the Midway. There will be a coned drift course with plastic barriers and a donut box.

Disclaimer: Salt City Drift is not affilitated with Miller Motorsports Park. All questions, comments and concerns should be directed to Nick Stucky at nickstucky@gmail.com.  

Date: September 6, 2014

Pre-Registration Fee: $90

Late Registration Fee(day of): $100

Tandem: $140

Tandem Late Registration: $150

Ride Along: $20

Helmet Rental: $10

New extended schedule:

Registration 7:00am - 8:00am
Tech  8:00am - 8:30am
Drivers Meeting  **Mandatory** 8:30am - 9:00am
Drift Course Open 9:00am - 12:00pm
Donut Box Open 9:00am - 12:00pm
Lunch  12:00pm - 1:00pm
Drift Course Open 1:00pm - 5:00pm
Donut Box Open 1:00pm - 5:00pm
Contest 4:00pm-5:00pm
Awards/Debrief 5:15pm - 5:30pm

                                        

            

         

           

                           

         

            

                          

Notes: No Tandem. One car on course at a time. Drivers are allowed to share a single car, two entry fee's must be paid. On-site tire changing services provided by Team D-Spare. Ace Cafe will be open for lunch. Closed toe shoes, pants and M rated helmet required. No shoes, no shirt....no drifting. 

Bring: Tools to fix your car, extra tires and plenty of water to drink.

All cancellations are subject to a $10 cancellation fee and require a MINIMUM 24 HOUR NOTICE. To cancel please contact: Jason D. Smith  801.918.6130  jdsmith@innovative-garage.com

Disclaimer: iDrift is not affilitated with Miller Motorsports Park. All questions, comments and concerns should be directed to: jdsmith@innovative-garage.com

Event requirements

DRFTutah Presented by http://innovative-garage.com/

Come enjoy an open drift day at Miller Motorsports Park in the Midway. There will be a coned drift course with plastic barriers and a donut box.

Disclaimer: Salt City Drift is not affilitated with Miller Motorsports Park. All questions, comments and concerns should be directed to Nick Stucky at nickstucky@gmail.com.  

Date: September 6, 2014

Pre-Registration Fee: $90

Late Registration Fee(day of): $100

Tandem: $140

Tandem Late Registration: $150

Ride Along: $20

Helmet Rental: $10

New extended schedule:

Registration 7:00am - 8:00am
Tech  8:00am - 8:30am
Drivers Meeting  **Mandatory** 8:30am - 9:00am
Drift Course Open 9:00am - 12:00pm
Donut Box Open 9:00am - 12:00pm
Lunch  12:00pm - 1:00pm
Drift Course Open 1:00pm - 5:00pm
Donut Box Open 1:00pm - 5:00pm
Contest 4:00pm-5:00pm
Awards/Debrief 5:15pm - 5:30pm

                                        

            

         

           

                           

         

            

                  

                          

Notes:  One car on course at a time. Drivers are allowed to share a single car, two entry fee's must be paid. On-site tire changing services provided by Team D-Spare. Ace Cafe will be open for lunch. Closed toe shoes, pants and M rated helmet required. No shoes, no shirt....no drifting. 

Bring: Tools to fix your car, extra tires and plenty of water to drink.

All cancellations are subject to a $10 cancellation fee and require a MINIMUM 24 HOUR NOTICE. To cancel please contact:  Nick Stucky at nickstucky@gmail.com.

Disclaimer: Salt City Drift is not affilitated with Miller Motorsports Park. All questions, comments and concerns should be directed to Nick Stucky at nickstucky@gmail.com.  

 

All Tandem Drifting participants must agree to abiding by the following rules:

Drift Utah - Rule Set

 

2 REQUIRED SAFETY EQUIPMENT

2.1 HELMET

Only helmets certified to meet the following standards are permitted:

•Snell Memorial Foundation – SA2005, SA2010 • SFI Foundation – 

Spec 31.2, Spec 31.2A

•British Helmet Standard – BS 6658:1958

 

2.2 HELMET VISOR

If the helmet has no visor eye protection must be worn 

 

2.3 DRIVING SUIT

One-piece driving suits are required and must be made of fire-resistant material and 

certified to SFI spec 3/2A-1 or greater, or homologated to “FIA 2000” specs, which 

effectively covers the body, including neck, ankles and wrists. Multi-layer driving suits 

are recommended.

Fire-resistant underwear is recommended. Fire resistant gloves, shoes, and socks are recommended. Socks must be made of fire-resistant material. Shoes and gloves must be made of leather, or any other approved fire-resistant material and must be free of holes, tears or other openings except those made by the manufacturer of the equipment.

 

2.4 RESTRAINT SYSTEMS

SFI Certification – Harness systems may be certified to SFI spec 16.1 or 16.5 and shall bear the appropriate label(s) on shoulder belts, lap belts and sub-straps. 

Each harness is punched with the year and month of manufacture. This certification 

shall expire (2) years after the punched month and date on the belt. SFI 16.1 belts 

must have a 3 inch lap belt. SFI 16.5 belts may have a 2 in lap belt. 2 in Head and Neck Restraint specific shoulders harnesses are permitted when used with an approved SFI 38.1 Head and 

neck restraint.

FIA Certification –Harness systems may be homologated by the FIA to specification 

8853/98, and shall bear the appropriate label(s) on each element of the belt. FIA belts 

are dated with an expiration year with the belts expiring on December 31st of the year 

punched or printed on the FIA tags.

Regardless of the date of manufacture, the safety harness shall be replaced if the 

webbing is cut/ frayed, if any of the buckles are bent/cracked, if the car has been in 

a severe impact, or at the direction of the TECHNICAL MANAGER. If any of these 

conditions exist, the TECHNICAL MANAGER shall cut the certification labels off of the 

harness. The team will then have to replace the belt.

 

2.5 SEATS

All cars must have a seat for the driver. Seats must be homologated to FIA standard

8855-1999 or SFI 39.2.

*If seats are not FIA compliant team must get a preapproved tech sticker prior to the 

competition.

 

2.6 ROLL CAGES

Roll cages are required.

2.6.1 BASIC DESIGN CONSIDERATIONS

A. 2013 competition vehicles may compete with a four point cage with single 

door bar minimum (on preapproval by GGD tech manager or chief steward). This is 

substantially less then you will need to move onto Formula Drift.

B. The basic purpose of the roll cage is to protect the occupant if the car turns over, 

runs into an obstacle, or is struck by another car. It shall be designed to withstand 

compression forces from the weight of the car coming down on the rollover 

structure and to take fore/aft and lateral loads resulting from the car skidding along 

on its rollover structure.

C. Forward braces and portions of the main hoop subject to contact by the occupant’s 

helmet (as seated normally and restrained by seatbelt/shoulder harness) shall be 

padded with non-resilient material. Ethafoam® or Ensolite®, or other similar material 

with a minimum thickness of one-half (1/2) inch and conforming to SFI spec 45.1 

is required. 

2.6.2 GENERAL CONSTRUCTION

All roll cages must be based on a single Main Hoop of one (1) continuous length of 

tubing with smooth continuous bends and no evidence of crimping or wall failure. 

The radius of bends in the roll cage hoop (measured at centerline of tubing) shall not 

be less than three (3) times the diameter of the tubing.

Welding shall conform to American Welding Society D1.1:2002, Structural 

Welding Code, Steel Chapter 10, Tubular Structures. Whenever D1.1 refers to “the 

Engineer” this shall be interpreted to be the owner of the vehicle. Welds shall be 

continuous around the entire tubular structure. All welds shall be visually inspected 

and shall be acceptable if the following conditions are satisfied:

1. The weld shall have no cracks.

2. Thorough fusion shall exist between weld metal and base metal.

3. All craters shall be filled to the cross section of the weld.

4. Undercut shall be no more than 0.01 inch deep.

Aluminum bronze or silicon bronze welding technique is permitted, but extreme care 

shall be used in preparation of parts before bronze welding and in the design of the 

attaching joints.

No portion of the cage may permeate the firewall and shall be fully contained within 

the occupant’s compartment.

The main components of the cage must be made of the same material, size and 

thickness of tubing.

2.6.3 ROLL CAGE MATERIAL

Seamless SAE 1020 or 1025, etc. mild steel tubing (DOM) is the preferred material 

for Roll Cage construction. Please contact GGD for approval if any alloy material 

will be used. An approved supplier MUST construct alloy steel cages. ERW tubing is 

not permitted.

2.6.4 INSPECTION HOLE

An inspection hole at least 3/16 inch diameter, but no greater than 1/4 inch 

diameter, shall be drilled in a non-critical area of all tubes to facilitate verification of 

wall thickness.

2.6.5 MAIN HOOP:

The main roll hoop (behind the driver) shall extend the full width of the 

driver/passenger compartment and shall be as near the roof as possible with a 

maximum of 4 bends, totaling 180 degrees ± 10degrees.

The roll cage Main Hoop should start from the floor of the car, and, in the case 

of tube frame construction, be attached to the chassis tubes by means of gussets 

or sheet metal webs with support tubes beneath the joints to distribute the loads. It 

is recommended that gussets be used.

The Main Hoop shall incorporate a diagonal lateral brace to prevent lateral 

distortion of the hoop. Any number of additional reinforcing bars is permitted within 

the structure of the cage.

A section of tubing equal to the roll bar shall be installed horizontally from the 

main hoop to the diagonal brace behind the drivers seat. This tube shall be no higher 

than shoulder height and continue from the diagonal to the passenger side main 

hoop upright.

2.6.6 FRONT/SIDE HOOPS:

The front hoops, side hoops, or down tubes shall begin at the floor.

Several configurations are allowed:

Side Hoop Configuration: Side Hoops connect directly from the floor of the occupant’s 

compartment and continue, in one piece, to connect to the Main Hoop. If Side Hoops 

are used, they are to be connected together by a single horizontal tube across the 

top of the windshield with a maximum of 4 bends totaling 90 degrees ± 10 degrees.

Front Hoop Configuration: A front hoop connected to the floor on both sides of the 

occupant compartment and following the line of the front pillars in one continuous 

piece may be used. A front hoop must be connected at the top by horizontal bars 

running back to the main hoop on each side, above the doors with a maximum of 

4 bends, totaling 180 degrees ± 10degrees.

HALO Configuration: A top “halo” hoop following the roofline in one continuous piece from each side of the main hoop along the tops of the doors and windshield. A HALO 

must be connected to the floor with forward “down tubes” following the line of the 

front pillars with a maximum of 4 bends, totaling 180 degrees ± 10degrees and a 

maximum of 2 bends allowed on the down tubes. The front, side or down hoops may 

extend through the dash pad, including the forward part of the door panel if it is an 

extension of the dash panel.

One (1) “Knee” bar is recommended in a horizontal plane between forward

cage braces in the dash area for all configurations.

2.6.7 REAR HOOP SUPPORTS:

The main roll hoop shall have two braces extending to the rear attaching to the frame 

or chassis. Braces shall be attached as near as possible to the top of the main 

hoop not more than six (6) inches below the top and at an included angle of at least 

thirty (30) degrees. No bends are allowed on rear braces. On cars where the rear 

window/bulkhead prohibits the installation of rear braces, the main hoop shall be 

attached to the body by plates welded to the cage and bolted to the stock shoulder 

harness mounting points.

2.6.8 BOLT IN ROLL CAGES

Bolt In roll cages are not allowed, unless welded in.

2.6.9 SUPPLEMENTAL BRACING:

Supplemental bracing is allowed.

2.6.10 SIDE PROTECTION:

All cars shall have a minimum of one (1) door bar across each front door opening. If 

two (2) bars are used, the door bars may run parallel, or in the shape of an “X”. If the 

two door bars do not intersect as they do when forming an “X”, then a minimum of 

two vertical tube sections shall connect the upper and lower door bars. Drivers may 

also choose to install a second row of double horizontal door bars that run parallel to 

the inner bars and extend into the outer door skin, these are also known as “NASCARSTYLE” bars. In this configuration, the outer bars must also have a minimum of two 

(2) vertical tube sections connecting the upper and lower bars. The inner door panel 

and door internals may be removed.

2.6.11 MOUNTING PLATES:

Each mounting plate shall be at least .080” thick.

2.6.11.2 

Mounting plates must be fully welded to the structure of the vehicle.

2.6.11.3 

Each mounting plate shall not be greater than 100 square inches and shall be no 

greater than twelve (12) inches or less than two (2) inches on a side. The mounting 

plate may be multi-angled but must not exceed these dimensions in a flat plane.

2.6.11.4 

Whenever possible, mounting plates shall extend onto a vertical section of the 

structure (such as a rocker box or door pillar).

2.6.11.5 

Any number of tubes may attach to a single plate or to each other.

*If car does not conform to these specs please contact GGD for tech inspection prior 

to competition by tech manager or cheif steward.

 

2.7 MOUNTING HARDWARE (BOLTS)

All hardware used in the mounting of seats, or other structural supports shall be SAE

Grade 5 or better with a 5/16” minimum diameter.

 

2.8 FIRE SUPPRESSION SYSTEM

All cars must be fitted with one fire-extinguishing bottle (2lb) mounted in the driver’s 

compartment within reach of the driver when he/she is in the normal seated position. 

The mounting bracket must be a quick-release type, and must be mounted so that it 

can be removed easily for label inspection and verification of full charge by weighing.

Acceptable extinguishants are Halon 1211, Halon 1301, Underwriters Laboratory

10BC rated Potassium Bicarbonate (Purple K), Underwriters Laboratory 1A10BC

Ammonium Phosphate/Barium Sulfate, or Monnex.

 

3.5 ELECTRICAL SYSTEM

3.5.1 MASTER CUT-OFF

A Master electrical cut-off switch, wired to completely shut off all engine and electrical 

system function (except for electrically operated fire suppression systems, if applicable) 

is mandatory and must mounted outside the vehicle, on the right side cowl just below 

the windshield and is to be clearly marked with the appropriate “OFF” markings.

The electrical terminals of the cut-off switch and/or any relays used in the circuit must 

be sufficiently insulated.

*Must conform to this by Round Two 2013 competition date.

3.5.2 BATTERY

The battery must be securely mounted and the positive terminal completely insulated 

to avoid contact with any other metal parts. Batteries may be relocated. If the battery 

is located in the driver’s compartment, it must in a sealed box bolted to the unibody/

chassis with the battery securely fastened inside the box and properly vented and 

drained.

 

3.6 BRAKE SYSTEM

The brake system must operate all 4 wheels.

 

3.7 ENGINE COOLING SYSTEM

Cooling system modifications are free but must be fully closed and free of leaks.

Cooling systems shall be filled with water only. “Water wetter” is allowed.

 

3.8 INTERIOR MODIFICATIONS

3.8.1 

The interior of the vehicle must be CLEAN and PROFESSIONAL in appearance. All 

non-essential and/or loose items must be removed. Any removable equipment such 

as spare tires, tools, bins, sub woofers, etc., shall be removed along with attaching 

hardware, brackets and covers.

 

DRIFT UTAH TECH MANAGER OR CHIEF STEWARD CAN CHANGE OR MODIFY THE RULE

BOOK DUE TO SAFETY OR CONCERN AT ANY TIME.

 

No shirt, no shoes......no drifting!

 

Miller Motorsports Park

Tooele, UT
Download track map
Download track map

Organizer

Drift organized by

Miller Motorsports Park - Box Office Registration

Event over!